States ›Texas ›Baylor County ›Seymour

Seymour, TX Tap Water Quality 2026

Water quality report for Seymour, TX — PFAS, lead and copper results, violation history and state inspection findings from EPA SDWIS.

A look at Seymour's drinking water using EPA enforcement records: violations, lead and copper results, PFAS sampling and state inspection findings.

Main Utility: City Of Seymour PWSID: TX0120001 Updated: 2026 Q2
✅

No federal limits exceeded on record

Lead is 1.10 ppb, 7% of the action level and no violations are open. PFAS has never been sampled at this system.

B

Seymour earns a B for water quality

Graded on violations and lead, with state inspection findings. PFAS not tested.

Lead: 1.10 ppb — 7% of the federal action level
PFAS never sampled at this system
8 violations since 2015, 0 health-based
No violations currently open
Seymour's lead level vs. all Texas community water systems
0 ppb5 ppb10 ppb15 ppb
Lead level: 1.10 ppb — 7% of the federal action level
✓ Lower lead than 78% of Texas utilities
Population Served
2525
~2403 connections
Water Source
Groundwater
Drawn from wells — SDWIS source code GW
Active Violations
0
8 since 2015, all resolved

Lead & Copper Testing

Lead (Pb)
90th percentile of tap samples collected across the distribution system
7% of EPA action level
1.10 ppb
Action level: 15 ppb
The 90th-percentile lead result is 1.10 ppb, 7% of the 15 ppb federal action level. The action level is a treatment trigger, not a legal maximum, and it is measured across sampled taps rather than at any single home.

Contaminant Violations (2015–Present)

ContaminantTypeMeasuredLimitPeriodStatus
Revised Total Coliform Rule MONITORING FAILURE — — 2025 Resolved
LEAD AND COPPER RULE REVISIONS REPORTING FAILURE — — 2025 Unaddressed
Lead and Copper Rule MONITORING AND REPORTING — TT 2024 Resolved
Public Notice OTHER — — 2024 Resolved
Revised Total Coliform Rule MONITORING FAILURE — — 2023 Resolved
Revised Total Coliform Rule MONITORING FAILURE — — 2019 Resolved
Coliform (TCR) MONITORING AND REPORTING — 5% of samples 2015 Resolved
Coliform (TCR) MONITORING AND REPORTING — 5% of samples 2015 Resolved
Understanding violation types MCL violations mean a contaminant exceeded the federal maximum limit — the most serious type.
TT (Treatment Technique) violations mean required treatment procedures weren't followed, but don't necessarily mean contamination occurred.

Violation History

8 violations are on record since 2015, of which 0 were health-based. All have been resolved and none remain open.

About the Main Water System

Utility City Of Seymour
PWSID TX0120001
Water source Groundwater — Drawn from wells — SDWIS source code GW
Population served 2,525
Service connections 2,403
Systems serving this area 2
Regulator State primacy agency
Data through 2026 Q2 — EPA SDWIS

Frequently Asked Questions

Is Seymour tap water safe to drink? ▼
No federal limit is exceeded on record. No violations are currently open. Lead is 1.10 ppb, 7% of the action level.
Does Seymour water have PFAS? ▼
This system has never been sampled for PFAS. EPA's national monitoring covered systems serving 3,300 people or more, so no results exist — which is not evidence that none is present.
Who supplies water to Seymour? ▼
City Of Seymour (PWSID TX0120001), one of 2 systems serving this area. Groundwater. Drawn from wells — SDWIS source code GW
When was this system last inspected? ▼
It was last inspected on 2025-03-24. Inspectors recorded 1 significant deficiency.

What Should Seymour Residents Do?

1
Read your annual water report
Your supplier publishes a Consumer Confidence Report each July covering the prior year.
2
Check for a lead service line
Lead reaches tap water mainly through service lines and household plumbing. Suppliers now publish an inventory identifying lead lines.
3
Flush before drinking
If water has sat in pipes more than six hours, run the cold tap for two minutes before drinking or cooking.

Nearby Cities in Texas