States ›Iowa ›Washington County ›Washington

Washington, IA Tap Water Quality 2026

Water quality report for Washington, IA — PFAS, lead and copper results, violation history and state inspection findings from EPA SDWIS.

A look at Washington's drinking water using EPA enforcement records: violations, lead and copper results, PFAS sampling and state inspection findings.

Main Utility: Washington Water Department PWSID: IA9271068 Updated: 2026 Q2
✅

No federal limits exceeded on record

Lead was not detected and no violations are open. No PFAS was detected.

A

Washington earns an A for water quality

Graded on violations, lead, and PFAS, with state inspection findings.

Lead: not detected
PFAS tested, none detected
4 violations since 2015, 0 health-based
No violations currently open
Washington's lead level vs. all Iowa community water systems
0 ppb5 ppb10 ppb15 ppb
Lead level: Not detected — 0% of the federal action level
✓ Lower lead than % of Iowa utilities
Population Served
7352
~2806 connections
Water Source
Groundwater
Drawn from wells — SDWIS source code GW
Active Violations
0
4 since 2015, all resolved

Lead & Copper Testing

Lead (Pb)
90th percentile of tap samples collected across the distribution system
0% of EPA action level
Not detected
Action level: 15 ppb
Lead was not detected at the 90th percentile — the result fell below the laboratory detection limit. That is not the same as an absence of lead in every tap, and older homes with lead service lines can still show higher readings.

Contaminant Violations (2015–Present)

ContaminantTypeMeasuredLimitPeriodStatus
Combined Radium (-226 and -228) MONITORING AND REPORTING — 5 pCi/L 2020 Resolved
Gross Alpha, Excl. Radon and U MONITORING AND REPORTING — 15 pCi/L 2020 Resolved
Revised Total Coliform Rule MONITORING FAILURE — — 2016 Resolved
Consumer Confidence Rule OTHER — — 2015 Resolved
Understanding violation types MCL violations mean a contaminant exceeded the federal maximum limit — the most serious type.
TT (Treatment Technique) violations mean required treatment procedures weren't followed, but don't necessarily mean contamination occurred.

Violation History

4 violations are on record since 2015, of which 0 were health-based. All have been resolved and none remain open.

About the Main Water System

Utility Washington Water Department
PWSID IA9271068
Water source Groundwater — Drawn from wells — SDWIS source code GW
Population served 7,352
Service connections 2,806
Systems serving this area 1
Regulator State primacy agency
Data through 2026 Q2 — EPA SDWIS

Frequently Asked Questions

Is Washington tap water safe to drink? ▼
No federal limit is exceeded on record. No violations are currently open.
Does Washington water have PFAS? ▼
It was tested for the six regulated PFAS compounds and none were detected.
Who supplies water to Washington? ▼
Washington Water Department (PWSID IA9271068). Groundwater. Drawn from wells — SDWIS source code GW
When was this system last inspected? ▼
It was last inspected on 2025-10-30. No significant deficiencies were recorded.

What Should Washington Residents Do?

1
Read your annual water report
Your supplier publishes a Consumer Confidence Report each July covering the prior year.
2
Check for a lead service line
Lead reaches tap water mainly through service lines and household plumbing. Suppliers now publish an inventory identifying lead lines.
3
Flush before drinking
If water has sat in pipes more than six hours, run the cold tap for two minutes before drinking or cooking.

Nearby Cities in Iowa

Kalona, Ia Tap Water Quality 2026 Washington Wellman, Ia Tap Water Quality 2026 Washington Riverside, Ia Tap Water Quality 2026 Washington Brighton, Ia Tap Water Quality 2026 Washington Ainsworth, Ia Tap Water Quality 2026 Washington Crawfordsville, Ia Tap Water Quality 2026 Washington