States ›Iowa ›Marshall County ›Melbourne

Melbourne, IA Tap Water Quality 2026

Water quality report for Melbourne, IA — PFAS, lead and copper results, violation history and state inspection findings from EPA SDWIS.

A look at Melbourne's drinking water using EPA enforcement records: violations, lead and copper results, PFAS sampling and state inspection findings.

Main Utility: Melbourne Water Supply PWSID: IA6471063 Updated: 2026 Q2
✅

No federal limits exceeded on record

Lead is 5.70 ppb, 38% of the action level and no violations are open. PFAS has never been sampled at this system.

B

Melbourne earns a B for water quality

Graded on violations and lead, with state inspection findings. PFAS not tested.

Lead: 5.70 ppb — 38% of the federal action level
PFAS never sampled at this system
No violations since 2015
No violations currently open
Melbourne's lead level vs. all Iowa community water systems
0 ppb5 ppb10 ppb15 ppb
Lead level: 5.70 ppb — 38% of the federal action level
✓ Lower lead than 13% of Iowa utilities
Population Served
786
~360 connections
Water Source
Groundwater
Purchased groundwater from another system — SDWIS source code GWP
Active Violations
0
None on record since 2015

Lead & Copper Testing

Lead (Pb)
90th percentile of tap samples collected across the distribution system
38% of EPA action level
5.70 ppb
Action level: 15 ppb
The 90th-percentile lead result is 5.70 ppb, 38% of the 15 ppb federal action level. The action level is a treatment trigger, not a legal maximum, and it is measured across sampled taps rather than at any single home.

Contaminant Violations (2015–Present)

✓ No violations on record for this water system.
Understanding violation types MCL violations mean a contaminant exceeded the federal maximum limit — the most serious type.
TT (Treatment Technique) violations mean required treatment procedures weren't followed, but don't necessarily mean contamination occurred.

Violation History

No violations are on record for this system since 2015. EPA records violations for every community water system, so this reflects a clean compliance history rather than missing data.

About the Main Water System

Utility Melbourne Water Supply
PWSID IA6471063
Water source Groundwater — Purchased groundwater from another system — SDWIS source code GWP
Population served 786
Service connections 360
Systems serving this area 1
Regulator State primacy agency
Data through 2026 Q2 — EPA SDWIS

Frequently Asked Questions

Is Melbourne tap water safe to drink? ▼
No federal limit is exceeded on record. No violations are currently open. Lead is 5.70 ppb, 38% of the action level.
Does Melbourne water have PFAS? ▼
This system has never been sampled for PFAS. EPA's national monitoring covered systems serving 3,300 people or more, so no results exist — which is not evidence that none is present.
Who supplies water to Melbourne? ▼
Melbourne Water Supply (PWSID IA6471063). Groundwater. Purchased groundwater from another system — SDWIS source code GWP
When was this system last inspected? ▼
It was last inspected on 2024-04-09. No significant deficiencies were recorded.

What Should Melbourne Residents Do?

1
Consider a filter certified for lead
Look for NSF/ANSI 53 certification for lead reduction.
2
Check for a lead service line
Lead reaches tap water mainly through service lines and household plumbing. Suppliers now publish an inventory identifying lead lines.
3
Flush before drinking
If water has sat in pipes more than six hours, run the cold tap for two minutes before drinking or cooking.

Nearby Cities in Iowa

Marshalltown, Ia Tap Water Quality 2026 Marshall State Center, Ia Tap Water Quality 2026 Marshall Le Grand, Ia Tap Water Quality 2026 Marshall Gilman, Ia Tap Water Quality 2026 Marshall Albion, Ia Tap Water Quality 2026 Marshall Liscomb, Ia Tap Water Quality 2026 Marshall